RE: [tkined] tkined and Solaris 8

From: John Karsten (john.karsten@home.com)
Date: Wed Jun 13 2001 - 21:55:47 MET DST


tkined and Solaris 8I tried a few different combinations and did get the
"noSuchName" response when reloading. I think its still not reading the
SNMP config that you added. This is the exact process I used to make this
work. I entered the correct community string into the SNMP-Monitor > Set
SNMP Parameter menu option. I am using a couple of different oids but you
can test it on Interface Load all. Select the node and then select
SNMP-Monitor > Interface Node All. You should now get the stripcharts for
all of the interfaces without any errors. Then select the stripchart that
you would like to keep and then right click and choose Create a New
Attribute. Under Name: enter "SNMP:Config" and under Value: I have entered
the following. Adapt the IP, version and community string to your needs.
"-address 192.168.1.1 -port 161 -version SNMPv2c -community
internet -timeout 5 -retries 3 -window 10 -delay 5". This resulted with the
following in my tki map file.

ined -noupdate attribute $stripchart1 SNMP:Config {-address
192.168.1.1 -port 161 -version SNMPv2c -community internet -timeout
5 -retries 3 -window 10 -delay 5}

Let me know how you made out.

John
  -----Original Message-----
  From: owner-tkined@ibr.cs.tu-bs.de [mailto:owner-tkined@ibr.cs.tu-bs.de]On
Behalf Of Kevin Campbell
  Sent: Wednesday, June 13, 2001 10:44 AM
  To: tkined@ibr.cs.tu-bs.de
  Subject: RE: [tkined] tkined and Solaris 8

  Well, I tried adding SNMP:Config to both the node and stripchart
definition resulting in the following lines in the .tki file.

  ined -noupdate attribute $stripchart1 SNMP:Config {-community RM7net}
  ined -noupdate attribute $node0 SNMP:Config {-community RM7net}

  I don't think I can call it progress, but now when I save and reload the
stripchart comes up with "noSuchName" instead of "noResponse".

  -----Original Message-----
  From: John Karsten [mailto:john.karsten@home.com]
  Sent: Tuesday, June 12, 2001 2:15 PM
  To: tkined@ibr.cs.tu-bs.de
  Subject: RE: [tkined] tkined and Solaris 8

  I had this as well and resolved it by adding the SNMP:Config attribute to
all of the nodes as well as the strip charts. I am using scotty-2.1.9.
    -----Original Message-----
    From: owner-tkined@ibr.cs.tu-bs.de
[mailto:owner-tkined@ibr.cs.tu-bs.de]On Behalf Of Kevin Campbell
    Sent: Monday, June 11, 2001 8:36 AM
    To: 'tkined@ibr.cs.tu-bs.de'
    Subject: [tkined] tkined and Solaris 8

    I was successfully running Tkined under Solaris 2.5.1, but it broke
after migrating to Solaris 8. It appears to work correctly, I can setup
devices and monitor them using SNMP. However, when I reload a config all of
the SNMP strip charts come up as "noResponse".

    I am running Scotty 3.0.0, Tkined 1.5.0, Tcl 8.3.3 and Tk 8.3.3. I have
tried setting the community with an SNMP:Config attribute, but this doesn't
seem to work. The same problem occurs with my old maps created under the
previous versions of Solaris and Tkined.

    Has anyone seen this behavior, and have a solution?

    Kevin Campbell - Maple Financial Group Inc.
    kcampbell@maplefinancial.com
    416-350-8255

--
!! This message is brought to you via the `tkined & scotty' mailing list.
!! Please do not reply to this message to unsubscribe. To subscribe or
!! unsubscribe, send a mail message to <tkined-request@ibr.cs.tu-bs.de>.
!! See http://wwwsnmp.cs.utwente.nl/~schoenw/scotty/ for more information.



This archive was generated by hypermail 2b29 : Thu Jan 03 2002 - 14:56:27 MET